Ubuntu和Debian8+ 上一鍵安裝并配置 WireGuard
,裝并sudo apt update,配置`,鍵安,裝并2. 安裝WireGuard軟件包:,配置??`,鍵安sudo apt install wireguard,裝并`,配置,鍵安3. 生成WireGuard??配置文件和密鑰:,裝并`,配置su??do wg genkey | sudo tee /etc/wireguard/privatekey | sudo wg pubkey > /etc/wireguard/publickey,`,,4. 創(chuàng )建WireGuard配??置??文件:,`,sudo nano /etc/wireguard/wg0.conf,`,,5. 將以下內容粘貼到配置文件中,然后保存并關閉文件:,`,[Int??erface],PrivateKey = /etc/wireguard/privatekey,Address = 10.0.0.1/24,ListenPort = 51820,,[Peer],PublicKey = /etc/wireguard/publickey,AllowedIPs = 10.0.0.2/32,Endpoint = peer(′ω`*).example.com:51820,PersistentKeepalive = 25,`,??,6. 啟動(′?_?`)WireGuard服務:,`,sudo systemctl enable wg-quick@wg0,sudo systemctl?? start wg-quick@wg0,`,,7. 確認WireGuard服務已啟動:,`,sudo systemctl status wg-quick@wg0,“,,現在,WireGu??ard已在Ubuntu和(╯°□°)╯︵ ┻━┻Debian 8+上安裝并配置完成。Ubuntu和Debian8+ 上一鍵安裝并配置 WireGuard
1. 安裝 WireGuard
在 Ubuntu 或 Debian 8+ 系統上,可以使用以下命令來安裝 WireGuard:
sudo aptg??et updatesudo aptget install wireguard
2. 生成密鑰對
WireGuard 使用公鑰和私鑰來進行身份驗證和加密,你需要為(′▽?zhuān)?你的 WireGuard(T_T) 客戶端和服務器生成密鑰對,可以使用以下命令生成:
wg genkey | tee privatekey | wg pubkey > publickey
這將生成一對公鑰和私鑰,并將它們分別保存在 privatekey 和 publickey 文件中(zhong)。
3. 配置 WireGuard 服務器
在服務器上,需要創(chuàng )建一個配置文件來設置 WireGuard,可以使用以下命令創(chuàng )建一個新的配置文件:
sudo nano /etc/wiregu??ard/wg0.conf將以下內容粘貼到配??置文件中,替換?? <your_public_key??> 和 <your_private_key&?gt; 為你在第2步中生成的公鑰和私鑰:
[??Interface](′Д` )PrivateKey = <your_private_key>ListenPort = 51820Address = 10.0.0.1/24[Peer]PublicKey = <your_public_key>AllowedIPs = 10.0.0.2/32
保存并關閉文件,使用以下命令啟動 WireGuard 服務器:
su(′▽?zhuān)?)do systemctl start wgquick@wg0sudo systemctl enable wgquick@wg04. 配置 WireGuard 客(ke)戶端
在客戶端上,也需要創(chuàng )建一個配置文件來設置 WireGuard,可以使用以下命令創(chuàng )ヾ(′▽?zhuān)??建一個新的配置文件:
nano /etc/wireguard/wg0.conf
將以下內容粘貼到配置文件中,替換 <your_public_key> 和 <your_privat(?Д?)e_key> 為你在第2步中生成的公鑰和私鑰,以及 <your_server_ip> 為你的 WireGuard 服務器的 IP 地址:
[Interface]PrivateKey = <your_private_key>Address = 10.0.0.2/32DNS = 8.8.8.8??,8.8.4.4[Peer]PublicKey = <y??our_publ(′?_?`)ic_key>AllowedIPs = 0.0.0.0/ヾ(?■_■)ノ0,::/0Endpoint = <your_server_ip>:51820Pers??istentKeepalive = 25保存并關閉文件,使用以下命令啟動 WireGuard 客戶端:
sudo systemctl start wgquick┐(′?`)┌@wg0
現在,你應該能夠在 WireGuard 服務器和客戶端之間建立連(lian)接了。
常見問題與解答
Q1: 如何查看 WireGuard 的狀態???
A1: 可以使用以下命令查看 WireGuard 的狀態:
sudo systemctl status wgquick@wg0
A2: 你可以直接編輯 /etc/wireguard/wg0.conf 文件來更改 WireGuard 的配置,完成更改后,需要重新啟動 WireGuarヽ(′▽?zhuān)?ノd 服務以應用更改:
sudo systemctl restart wgquick@wg0





